Introduction: A concrete pump cutting ring is the ring at the S-valve end that slides across the spectacle wear plate in the hopper. Many parts lists call the same part a wear ring. To identify it, do not rely on the name. Read the OEM number and any DN or grade mark on the removed ring, note which spectacle wear plate it runs against, and check the pump nameplate. Then order the aftermarket replacement by that OEM number.
This guide explains where the ring sits, why two names are used, what to read on the old part, and which nearby parts are often mistaken for it. If you already know the ring and plate are both worn, see Concrete Pump Spectacle Wear Plate and Cutting Ring: When to Replace Them as a Set.
On an S-valve concrete pump, the spectacle wear plate is fitted in the hopper at the openings that lead to the two delivery cylinders. The cutting ring is fitted at the S-valve end and slides across that plate each time the valve changes over. The ring and the plate form the sealing and wear face between the valve and the cylinders.
A rock-valve pump uses a different set of valve wear parts. Do not treat an S-valve cutting ring as a rock-valve part because the names sound alike. The difference between the two valve types is explained in S-Valve vs Rock Valve on a Concrete Pump.
The term also has another meaning outside concrete pumps: a cutting-ring fitting is a type of hydraulic pipe fitting. That is a different item. When you search or request a quote, keep the words concrete pump with the part name.
Cutting ring and wear ring are two catalog names for the ring that runs against the spectacle wear plate. Which name appears depends on the brand, the parts list, and the seller. The name does not decide fitment. The OEM number does.
Examples on this site show how the names cross over:
So a buyer asking for a Putzmeister cutting ring and a buyer asking for a Putzmeister wear ring may need the same part, or two different parts. Only the OEM number and size settle it.
Before you order, collect what identifies the ring you are replacing:
If a mark is worn away, say so. Photos and the nameplate details are better than a guessed number.
A matching DN does not make two rings interchangeable. Putzmeister examples show why:
The same logic applies to the plate. A ring is matched to a plate. If the plate grade or OEM changes, check the ring as well. Material designations for wear plates are compared in DURO 22 Wear Plate vs Carbide Wear Plate for Concrete Pumps.
Send the pump brand, model, and serial number; the OEM number of the ring and of the spectacle wear plate; any DN or grade mark; and photos of the old ring. State that you need an aftermarket replacement cutting ring or wear ring for a concrete pump. We check the number and size against our records before we quote.
A concrete pump cutting ring and a wear ring are usually two names for the same job: the ring at the S-valve end that slides across the spectacle wear plate. Identify it by OEM number, DN or size, grade mark, and the plate it runs against, not by the catalog name or by size alone.
A: It is the ring fitted at the S-valve end that slides across the spectacle wear plate in the hopper. Together, the ring and the plate form the sealing and wear face between the valve and the delivery cylinders.
A: Often the two names describe the same job, and some listings use both for one OEM, such as 261123001. But two rings with different OEM numbers are different parts, even when both are called a wear ring or a cutting ring. Order by the OEM number on the removed ring or the parts list.
A: Read the OEM number and any DN or grade mark on the old ring, note the OEM number of the spectacle wear plate it runs against, and check the pump nameplate. Send those details with photos of both faces of the ring.
A: No. Rings of the same DN can have different OEM numbers and grades. For example, 261123001 (DURO 22) and 494520 (HM) are listed for the same Putzmeister DN230 position.
A: Inspect both. The ring and the plate wear against each other, and they are usually replaced as a set when either face is worn. The set-replacement guide linked in this article covers what to check.
A: The pump brand, model, and serial number; the OEM numbers of the ring and the spectacle wear plate; any DN or grade mark; and photos of the old ring. If a number is unreadable, say so and let the photos and nameplate carry the identification.
Putzmeister, Schwing, SANY, CIFA, and Zoomlion are trademarks of their respective owners. The parts described here are aftermarket replacements, not OEM parts made by those manufacturers. Brand names and OEM numbers are used for reference only.