This delivery piston seal with guide ring is the part that takes the wear at the concrete end of a pump. Mounted on the delivery piston inside the cylinder, it holds pressure behind the concrete on the pushing stroke and keeps the abrasive mix from working back past the piston. This set covers the 200 mm delivery cylinder and arrives as a matched pair — seal plus guide ring — because the two are changed together in normal service. It is an aftermarket replacement, and the Putzmeister numbers and name are used here as a cross-reference only, so you can match the part to the machine in front of you. As a concrete pump piston seal supplier, we send this size to three kinds of buyer: service workshops rebuilding a delivery cylinder on the bench, distributors who restock a wear item that moves steadily, and fleet maintenance teams who would rather have the seal on the shelf than wait for one. It is ordered alongside the delivery piston ram, the cylinder seal kits and the S-valve parts that come off the same area of the pump during a rebuild.
Fitment Check for DN200 Delivery Cylinders
Confirm the bore size first. Every DN200 Putzmeister piston seal we supply is made for a 200 mm nominal delivery cylinder, so check the cylinder bore or the diameter marked on the old piston before you price the job.
Read both numbers off the old parts. The seal and the guide ring are listed under separate OEM references, and after a hard season the ring number is sometimes the only one still legible.
Match the piston ram at the same time. The seal fit depends on the piston it sits on, so if the ram is being replaced as well, quote both so we can check they belong together.
Do not substitute another diameter. Seals for DN180, DN230 or DN280 cylinders sit in the same family but will not seat in a 200 mm bore.
Flag a converted machine. If the delivery cylinder, the piston type or the pump end has been changed since the pump was built, say so — that is where most wrong-fit orders for concrete pump wear parts start.
Seal and Guide Ring Working Pair
The two components do different work. The seal is the soft element: its lip rides against the cylinder bore, holds pressure behind the concrete and absorbs the abrasion. The guide ring is the structural half — it centres the piston in the bore, carries side load and keeps the piston body off the cylinder wall. Replace them as a pair. A ring that has worn thin lets the piston sit slightly off-centre, so the seal lip loads unevenly: one side scrubs while the other barely touches. That seal fails early, and the failure usually gets blamed on the seal rather than the ring underneath it. Fitting a new seal onto a worn ring is the most common way to do this job twice. The ring also sets how the seal sits against the bore, because its height and fit control how much the seal is compressed. That is why the two are matched and supplied together rather than picked separately out of a parts bin. At rebuild, judge both. Keep each seal with its own ring. If two sets are going onto two pumps, do not swap the halves, because a seal matched to a ring from another set can sit at the wrong compression. Until they are fitted, store them flat and out of direct sunlight. This is the DN200 delivery piston seal for concrete pump service at the 200 mm cylinder size, with the ring matched to it.
Wear Signs and Replacement Timing
Pressure that will not hold. A pump that struggles to build delivery pressure, hesitates at changeover or needs more engine speed for the same line is often telling you the DN200 delivery piston seal is passing.
Material where it should not be. Concrete or mortar working past the piston instead of going up the pipeline is the clearest sign the seal has stopped sealing. Clean it out before it reaches the hydraulic end.
A lip that has lost its edge. At inspection, a seal that is hard, glossy, cracked or flattened across part of the lip has lost the elasticity it needs. Heat and age do this even on a part with few running hours.
A guide ring with a step. Ring wear is easy to miss because the damage sits on the running face: look for a polished flat, a lip at the edge or fine cracks.
Running hours set the rhythm, not the calendar. Abrasive aggregate, high pumping pressure, long lines and heavy shift work all shorten seal life, so two pumps doing similar hours can need seals months apart. Track hours per pump instead of relying on a fixed interval.
One worn part hides another. If pressure does not come back after a new seal and ring, check the other concrete pump wear parts around it — the piston ram for scoring, the S-valve, the cylinder bore — before blaming the new set.
Installation and Break-In
Isolate and wash down. Depressurise the pump, drain the delivery line and clean the concrete end so grit from the hopper does not end up between the new seal and the bore.
Inspect the cylinder before anything is fitted. Run a hand and a light down the bore. Scoring, a burr at the mouth or hardened concrete on the wall will cut a new seal during the first strokes, so deal with it before reassembly.
Strip the old delivery piston seal with guide ring in the order it came off the piston. Note which way the seal lip faces, or photograph the assembly before you take it apart — reassembly is much easier with a reference.
Seat the guide ring first, square to the piston. It should go on without force. If it needs to be driven, either the size is wrong or there is debris in the groove.
Fit the Putzmeister piston seal with the lip toward the concrete side, working it over the piston evenly with a blunt tool — never a screwdriver — and lubricate the lip with a lubricant your workshop already uses for seal assembly.
Slide the piston in squarely and bring the delivery end back together following the pump maker's procedure, keeping the seal lip away from sharp edges as it enters the bore.
Break in gently and log it. Run the first strokes at low pressure and watch the delivery end for weeping, a hot cylinder or a pressure drop. Note the date and pump hours in the maintenance log so the next change can be planned rather than forced.
Specifications
Property
Detail
Part name
DN200 delivery piston seal with matching guide ring
Nominal size
DN200 / Ø 200 mm
Dimensions
200 mm x 180 mm x 40 mm
OEM reference, seal
080372004
OEM reference, guide ring
080794006
Machine application
Putzmeister concrete pump delivery cylinders
Category
Putzmeister spare parts / concrete pump spare parts
Part status
Aftermarket replacement, not made by Putzmeister
Brand reference
Putzmeister is a trademark of its owner; numbers are used for reference only
Ordering, Payment & Delivery
Property
Detail
Payment terms
T/T or L/C
Dispatch
Normally 3–5 days after the order is confirmed
Carriers
FedEx, DHL, EMS or UPS
Transit time
Normally 3–7 days; holidays or events beyond our control may add a few days
Tracking
Carrier name and tracking number sent when the parcel ships
Shipping coverage
Worldwide shipping
Delivery address
Please check that the address and contact details on the order are complete and correct
Returns window
15 days from receipt; check the parts as soon as they arrive
Return authorisation
Email us before sending anything back and we reply with the return address
Return shipping
Buyer's cost unless the parts arrived faulty or damaged
Refund
Issued once the returned parts are received and checked; the payment reaches your account a few days later
Catalogue
Full-range parts catalogue available from our team
Contact
WhatsApp +86 19545516660; joak816@outlook.com
Technical Support & Model Matching
Not sure a part will fit? Send us the OEM number, the machine model or a photo of the part you are replacing, and our technical team will check it against our records and confirm before you order. Founded in 2009, CZIC GROUP supplies concrete pump wear parts and construction machinery spares worldwide, with agents in more than 20 countries. We help buyers with part matching, fault diagnosis and installation or commissioning questions, before and after they order.
Specs
OEM: 080372004
Part name: Delivery Piston Seal DN200 with Guide Ring
No. It is an aftermarket replacement referenced to Putzmeister OEM number 080372004.
Which delivery cylinder does the DN200 delivery piston seal fit?
Delivery cylinders with a 200 mm nominal bore, DN200. The set measures 200 mm x 180 mm x 40 mm and includes the guide ring. A pump with a different cylinder size takes a different seal, so check the bore or the reference on the old seal before ordering.
Does the guide ring come with the seal?
Yes. One order covers both halves of the pair: the delivery piston seal with guide ring arrives as a single set, so there is no second line to add when you price a rebuild. Distributors restocking the item can quote it under one entry and still show the ring's own OEM number to a customer who asks for it by that reference. Some workshops already hold a sound ring and want only the seal, or the other way round; because the two are catalogued separately, send the reference for the half you need and we will confirm what can be supplied on its own. On arrival, count both components before the cylinder goes back together and check the ring against the reference you expect, since a ring from a neighbouring bore size can look very close on the bench. Keep the set together until the rebuild — a loose ring on a shelf is easily filed into the wrong box.
How is a delivery piston seal different from a piston ram?
The piston ram is the piston body itself — the part that transmits force and pushes concrete through the cylinder. The seal is the wearing element mounted on it, and the guide ring travels with the seal. They are separate parts under separate references, so a rebuild can call for the set, the ram, or both, depending on what the workshop finds.
Will this set fit a pump from another manufacturer?
It is listed for Putzmeister delivery cylinders at the DN200 size. Other makes use their own piston and seal geometry, so this DN200 delivery piston seal for concrete pump use on a Schwing, SANY, Zoomlion or CIFA machine needs checking first — send the OEM number or the bore measurement and we will confirm whether it matches or which set does.
You can send money by T/T Or L/C
We have been committed to providing customers with fast, reliable logistics delivery services. Shipping & Tracking We normally dispatch parts within 3–5 days after receiving your order. Once your order ships, we send you the carrier name and tracking number. Most orders ship by FedEx, DHL, EMS or UPS and take 3–7 days to arrive. Holidays or events beyond our control (such as earthquakes or hurricanes) may add a few days. Please make sure your shipping address and contact details are complete and correct. The carrier name and tracking number are in your shipping confirmation email, and you can track the parcel on the carrier's website. Returns & Refunds We offer a 15-day guarantee from receipt of the parts. Please check the parts as soon as they arrive. Before returning anything, contact us by email and we will send you the return address. The buyer pays return shipping unless the parts arrived faulty or damaged. Once we receive the return and confirm there is no problem, we refund you. The refund reaches your payment account within a few days.