On a Putzmeister concrete pump, wear ring and cutting ring are two catalog names for the ring that runs against the spectacle wear plate in the hopper. The name on a listing is not the order identity. Confirm the OEM number on your parts list, or on the removed ring, before you order an aftermarket replacement. Do not treat two listings as interchangeable just because one is titled wear ring and the other is titled cutting ring.
This article explains how those names appear in Putzmeister catalogs and how to order by OEM number. It does not repeat the general identification steps, and it does not cover every brand. For how to identify a cutting ring or wear ring on a concrete pump, see How to Identify a Concrete Pump Cutting Ring (and Wear Ring). If the ring and the spectacle wear plate are both worn, see Concrete Pump Spectacle Wear Plate and Cutting Ring: When to Replace Them as a Set.
A Putzmeister wear ring is a concrete-pump part: the ring at the S-valve end that slides across the spectacle wear plate each time the valve changes over. Many Putzmeister parts lists and aftermarket catalogs call the same kind of part a cutting ring. Both names describe that hopper / S-valve wear job. Neither name, by itself, tells you which OEM number your pump uses.
This is not a generic industrial wear ring, and it is not a hydraulic cutting-ring pipe fitting. Keep the words Putzmeister and concrete pump with the part name when you search or request a quote.
Which name you see depends on the parts list and the seller, not on a second, hidden part type. Confirmed examples on this site show the crossover:
So a buyer asking for a Putzmeister wear ring and a buyer asking for a Putzmeister cutting ring may need the same part, or two different parts. Only the OEM number and the size and grade marks settle it.
A matching name or a matching DN does not make two rings the same part.
If one page is titled "cutting ring" and another is titled "wear ring," read the OEM number on each listing. Do not assume the two pages are the same part, and do not assume they can be swapped.
Order by the OEM number on the removed ring or on the parts list for your pump's serial number. Record any DN or other size mark, any grade mark such as DURO 22 or HM, and the OEM number of the spectacle wear plate the ring runs against. If a mark is worn away, send photos and the nameplate details rather than guessing a number.
What to read on the old ring is covered in How to Identify a Concrete Pump Cutting Ring (and Wear Ring). State that you need an aftermarket replacement wear ring or cutting ring for a Putzmeister concrete pump. We check the OEM number and marks against our records before we quote.
The ring and the spectacle wear plate wear against each other. When you change one, inspect the other. They are often replaced as a set. That check is explained in Concrete Pump Spectacle Wear Plate and Cutting Ring: When to Replace Them as a Set; this article does not repeat the set-replacement guide.
On a Putzmeister concrete pump, wear ring and cutting ring are two catalog names for the same kind of hopper / S-valve ring. Order the aftermarket replacement by the OEM number that belongs to your machine. The catalog name, and size alone, are not enough. Do not treat two listings as interchangeable until the OEM numbers match.
Q: Is a Putzmeister wear ring the same as a cutting ring?
A: Often the two names describe the same job, and some listings use both for one OEM, such as 261123001. The catalog name is not the identity. Two rings with different OEM numbers are different parts. Order by the OEM number on the removed ring or the parts list.
Q: Wear ring or cutting ring Putzmeister — which name should I search?
A: You can search either name, but send the OEM number when you request a quote. A result titled wear ring and a result titled cutting ring may be the same OEM, or two different parts.
Q: How long does a wear ring last?
A: There is no single service-life figure that applies to every Putzmeister wear ring or cutting ring. Inspect the wear face and replace the ring by the OEM number that belongs to your pump. The ring and the spectacle wear plate often wear together; see Concrete Pump Spectacle Wear Plate and Cutting Ring: When to Replace Them as a Set for when to replace them as a set.
Q: Can I treat two Putzmeister rings as the same part if both are DN230?
A: No. DN is a size class, not a complete identity. For example, 261123001 is listed as a DN230 DURO 22 wear ring / cutting ring, and 494520 is listed as the HM wear ring for that DN230 position. They are different OEM numbers.
Q: Should I replace the spectacle wear plate with the Putzmeister wear ring?
A: Inspect both. The ring runs against the spectacle wear plate, and they are usually replaced as a set when either face is worn. The set-replacement guide linked in this article covers what to check.
Q: What should I send when I request a Putzmeister wear ring or cutting ring quote?
A: The pump brand, model, and serial number; the OEM number of the ring and of the spectacle wear plate; any DN or grade mark; and photos of the old ring. If a number is unreadable, say so and let the photos and nameplate carry the identification.
Putzmeister, Schwing, SANY, CIFA, and Zoomlion are trademarks of their respective owners. The parts described here are aftermarket replacements, not OEM parts made by those manufacturers. Brand names and OEM numbers are used for reference only.