• 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump

066600004 Hydraulic Accumulator 4.0L for Putzmeister Concrete Pump

No.066600004

066600004 hydraulic accumulator 4.0L, aftermarket for Putzmeister. Send OEM no. for a quote.

  • Description

  • Payment Method

  • Shipping&Returns

  • Contact Us

Complete Unit vs Bladder

Two parts in this size are easily confused, and mixing them up is the most common ordering error on this item. This listing is the 4L hydraulic accumulator itself — the complete vessel, with its shell, gas valve, oil connection and bladder already assembled. The other part is the 4.0 L bladder on its own: the flexible element that separates gas from oil, and the part you fit when an accumulator with a sound shell is being rebuilt rather than replaced.

Choose the complete unit when the shell is pitted or corroded, when the gas valve will not hold or its seat is marked, when the oil port thread or sealing face is damaged, or when the history of the unit is unknown and you do not want to open the same accumulator twice. Choose the bladder alone only when the shell and valve are known good and the failure is clearly the rubber element.

A re-bladdered accumulator still carries the old shell's fatigue and corrosion, so on a pump that runs long shifts many workshops replace the complete unit and keep the failed one on the shelf as a spare shell for a bladder job later.

Product Overview

A 4L hydraulic accumulator is the pressure store on the hydraulic side of a concrete pump: a sealed vessel with a gas charge on one side and hydraulic oil on the other, working every time the machine strokes. This listing is the complete 4.0 L unit — shell, gas valve, oil connection and bladder already assembled — supplied from our concrete pump spare parts range as an aftermarket replacement for the accumulator the pump was built with.

In service it does two jobs at once. It takes the pressure peaks that build each time the two delivery cylinders swap over, and it gives back stored oil in a short burst when the circuit needs flow faster than the main hydraulic pump can deliver it. The result is a changeover that stays crisp, less shock travelling into the valve block, hoses and pump, and a system that holds a steadier working temperature.

These units are usually bought for one of three reasons: the changeover has gone slow or harsh, oil has started showing at the gas valve, or the machine is in for a hydraulic overhaul and the accumulator is being renewed as part of it. Pump workshops, distributors and fleet maintenance teams are the usual buyers — and where several machines list the same unit, one accumulator in the stores often covers the whole group.

Function in the Pump Circuit

As a 4L hydraulic accumulator for concrete pump hydraulic circuits, this unit sits between the main hydraulic pump and the valves that do the fast work, and its condition shows up in how the machine behaves rather than on a gauge alone.

The changeover is where it earns its place. Moving the S-valve or S-tube from one delivery cylinder to the other needs a slug of oil in a fraction of a second — far more flow than the main pump can produce on its own. The accumulator supplies that surge and then recharges between strokes. It also damps the pressure peaks created as each delivery cylinder reaches the end of its stroke, so the valve block, hoses and hydraulic pump see a smoother curve instead of a hammering.

On a pump with a tired accumulator, that work moves back to the hydraulic pump. Changeover slows, pressure spikes travel further through the circuit, oil temperature climbs, and the pump is asked to do a job it was not sized for. Renewing the accumulator puts the circuit back the way it was designed to run.

Specifications

Property Detail
Part name Hydraulic accumulator
Nominal volume 4.0 L
OEM reference 066600004
Type Bladder-type accumulator, supplied as a complete unit
Build Shell, bladder, gas valve and oil connection assembled as one piece
Application Putzmeister concrete pump hydraulic systems
Category Concrete pump spare parts
Part status Aftermarket replacement, not a OEM part
Identification Match the reference on the original unit before ordering

Hydraulic Oil Compatibility

  • Mineral hydraulic oil is the reference fluid — the oil port, the sealing face and the bladder inside this 4L hydraulic accumulator are matched to the mineral-based oil these concrete pumps normally run. Use the viscosity grade and specification your pump manual calls for rather than whatever grade happens to be in the workshop.
  • Say so before ordering if the machine runs a non-mineral fluid — fire-resistant fluids, water-glycol and biodegradable ester fluids behave differently with the elastomer inside an accumulator, and some will soften or swell a bladder that is perfectly happy on mineral oil. Send us the fluid brand and type, or the data sheet, and as a hydraulic accumulator supplier we will confirm compatibility before the unit ships.
  • Never mix fluid families on a top-up — on a second-hand pump or a mixed fleet, the safest move is to draw a sample and have it identified before anything is added. A blended fill is one of the quickest ways to shorten the life of a new accumulator.
  • Cleanliness counts as much as the grade — grit that reaches the oil port scores the sealing face and works its way towards the bladder. Fill through a filtered unit, keep caps and couplings capped, and change the return filter when the accumulator is renewed.
  • Watch for water in the oil — moisture leaves corrosion on the inner wall of the shell and on the gas valve seat. If the oil is milky or a drain shows water, deal with that first; otherwise a replacement unit simply starts the same decline.
  • Match the grade to the working climate — oil that is too thick for the ambient temperature leaves the circuit slow to recharge between strokes and loads the hydraulic pump at start-up. Choose the grade for the conditions the pump actually works in.
  • Sample the oil and change the filter at the swap — when you fit this 4L hydraulic accumulator, pull an oil sample for analysis at the same time, so the new unit is not fed the debris that finished the old one.

Installation and Pre-Charge

  1. Shut the machine down and relieve the hydraulic pressure exactly as the pump manual describes — an accumulator holds pressure after the engine stops, so no fitting comes loose until the circuit is discharged.
  2. Photograph the old unit before you take it out: gas valve position, oil connection, bracket and hose route. Four pictures on a phone save an hour of guessing on reassembly.
  3. Compare old and new on the bench — port thread, sealing face, overall height and valve position. If anything differs, stop and talk to us before fitting it.
  4. Fit the new unit with a new seal at the oil connection. A hardened old washer is one of the most common causes of a weep after a fresh installation.
  5. Set the gas pre-charge to the pressure the pump manufacturer specifies for your model, using dry nitrogen. Never use oxygen or compressed air, and never take a default figure from a general guide — the correct pre-charge depends on the circuit.
  6. Start on low pressure, run through several changeover cycles, and check the oil connection and gas valve before the machine goes back to work.

Service Life and Maintenance

  • Check the pre-charge at every major service — slow gas loss through the valve is the most common reason an accumulator starts to feel tired, and it is invisible from the outside.
  • Look for oil at the gas valve — oil on the gas side means the bladder has failed; catching it early keeps the rest of the circuit clean.
  • Judge it by the changeover — if changeover has become slower or harsher over a few weeks, test the accumulator before anyone blames the valve block or the main pump.
  • Keep the shell dry and painted — external corrosion decides whether a unit can be re-bladdered later, and it is the reason most complete replacements are bought at all.
  • Never weld, drill or modify the shell — it is a pressure vessel, not a fabrication item, and a repair like that has no place on a working pump.
  • Replace rather than rebuild when the valve seat is damaged — a shell that will not seal will not hold a pre-charge whatever bladder goes inside it.
  • A 4L hydraulic accumulator in the stores covers the fleet — where several machines list the same unit, one spare keeps a pump from standing while a part is on order.

Ordering and Delivery

What you need to check the part before it ships can be sent ahead of the order: the specification sheet for this accumulator, photographs of the actual unit held in our stores, and — where a fit question remains — a simple dimensioned sketch showing overall height and the position of the oil port, so you can lay it against the old accumulator on the bench. Our concrete pump spare parts catalogue is available as a download if you would rather browse the range yourself first. If you have the pump's parts manual page, send that. If not, a clear photo of the plate on the old accumulator and of both connections is usually enough to work from. As a hydraulic accumulator supplier we would rather spend ten minutes on a fit question before the order than have a unit sit on a shelf because the port thread turned out to be different.

Payment T/T or L/C
Shipping Worldwide shipping
Dispatch Normally 3–5 days after your order is received
Carriers FedEx, DHL, EMS or UPS
Transit time Typically 3–7 days from dispatch
Tracking Carrier name and tracking number sent when the parcel leaves
Returns Accepted within 15 days of receipt — contact us first for the return address
Return freight Buyer's cost unless the part arrived faulty or damaged
Refund Issued once the returned part has been checked; the amount reaches your account within a few days
Supply range Concrete pump spare parts, seals, valves and hydraulic pumps
Contact WhatsApp +86 19545516660 · joak816@outlook.com

Technical Support & Model Matching

Not sure a part will fit? Send us the OEM number, the machine model or a photo of the part you are replacing, and our technical team will check it against our records and confirm before you order. Founded in 2009, CZIC GROUP supplies construction machinery spares worldwide, with agents in more than 20 countries. We help buyers with part matching, fault diagnosis and installation or commissioning questions, before and after the sale.

FAQ

How do I confirm this accumulator fits my pump?

Start with the number on the old unit and the parts page for your pump model. Send us either — or a photo of the plate and both connections — and we will check it against this 4L hydraulic accumulator for concrete pump circuits before you order. On the bench, compare port thread, mounting and overall height first; those are the three details that most often differ between units that look identical.

Is this a Putzmeister part?

No. It is an aftermarket replacement supplied from our Putzmeister spare parts range and sold on the OEM reference so you can match it to your machine; brand names and OEM numbers are used for reference only. We are a hydraulic accumulator supplier, not the pump manufacturer, and we would rather say so plainly than let an assumption travel with the box.

What does the 4.0 L figure refer to?

It is the nominal gas volume of the accumulator. The pump manufacturer chose that volume to suit the oil demand and pre-charge of the circuit, so replacing like for like matters more than it looks: a different volume with the same connections will physically fit and still change how the changeover behaves.

Which hydraulic oil can it run with?

The oil side is built for the mineral hydraulic oil these pumps normally use. If your machine has been converted to a different fluid, or you are unsure what has been topped up over the years, tell us before ordering and we will confirm compatibility rather than leave it to chance.

Can it be used on other machines besides concrete pumps?

If another machine's parts list quotes the same reference, yes — matching is done by number, not by the badge on the panel. What we would not do is fit a unit by volume alone, because port size, mounting and pre-charge all have to agree with the circuit it is going onto.

Does it arrive ready to fit?

It arrives as the assembled unit. The gas side still has to be set and checked to the pressure your pump manufacturer specifies before the machine goes back into service, because that figure changes with the model and the circuit. Have dry nitrogen and a charging kit on hand before you remove the old accumulator, so the pump is not standing idle waiting for them.

You can send money by T/T Or L/C
We have been committed to providing customers with fast, reliable logistics delivery services.
Shipping & Tracking
We normally dispatch parts within 3–5 days after receiving your order. Once your order ships, we send you the carrier name and tracking number.
Most orders ship by FedEx, DHL, EMS or UPS and take 3–7 days to arrive. Holidays or events beyond our control (such as earthquakes or hurricanes) may add a few days.
Please make sure your shipping address and contact details are complete and correct.
The carrier name and tracking number are in your shipping confirmation email, and you can track the parcel on the carrier's website.
Returns & Refunds
We offer a 15-day guarantee from receipt of the parts. Please check the parts as soon as they arrive.
Before returning anything, contact us by email and we will send you the return address. The buyer pays return shipping unless the parts arrived faulty or damaged.
Once we receive the return and confirm there is no problem, we refund you. The refund reaches your payment account within a few days.
Whatsapp:+86 19545516660
Email:joak816@outlook.com
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump
  • 066600004 hydraulic accumulator 4.0L for Putzmeister concrete pump

Download

CONTACT US

If you have any queries, get in touch today! Don't hesitate. We try to take the extra step for our customer satisfaction.
Name
Email *
Message
Leave a message
Name
Email *
Message
We use Cookie to improve your online experience. By continuing browsing this website, we assume you agree our use of Cookie.
Message Us