• 086877008 Hydraulic Cylinder Seal Kit 140/120mm
  • 086877008 Hydraulic Cylinder Seal Kit 140/120mm

086877008 Hydraulic Cylinder Seal Kit 140/120mm

No.086877008

Category: Putzmeister Spare Parts

Part Name: Hydraulic Cylinder Seal Set - 140mm/120mm

OEM NO.: 086877008

  • Description

  • Payment Method

  • Shipping&Returns

  • Contact Us

Wear Symptoms

What the operator noticesWhat it usually indicates
Oil film or a drip on the piston rodRod seal or wiper has worn through
Cylinder creeps or drifts under loadPiston seal bypassing oil inside the barrel
Pump loses delivery pressure or short-strokesPressure escaping past worn piston seals
Oil level dropping with no puddle under the machineInternal leakage passing across the piston
Seals hard, flattened or cracked at strip-downLong service and heat; the rubber has taken a set
Concrete dust or slurry packed behind the wiperWiper no longer scraping, so grit is reaching the rod seal
Seal lip cut or torn as the cylinder came apartDamage from the last assembly, a sharp edge or a dry fit

Product Overview

The cylinder it serves sits at the centre of the pump's hydraulic drive. Oil pressure pushes the piston, the piston drives the rod, and the rod drives the concrete piston in the delivery cylinder. Every seal along that chain works against oil under pressure on one side and concrete dust, wash-down water and site weather on the other, which is why they wear out. Buyers come to this kit in two situations. The planned one is a rebuild: the machine is in the workshop, the cylinder is already open or due to come off, and the seals are being renewed before they fail. The urgent one is a failure — the pump is down, it is not building pressure, and the kit has to be on its way. Concrete pump workshops rebuilding customer machines, fleet maintenance teams working to a service interval, and parts distributors looking for a dependable hydraulic cylinder seal kit supplier all order it. If you maintain mixed-brand equipment, order by the number and the size pair rather than by the machine name.

What the Kit Covers

  • Piston seal — the main pressure seal on the piston, holding the oil that does the pushing. Once it wears, oil slips past the piston and the cylinder stops holding load or loses stroke.
  • Piston guide ring (wear ring) — keeps the piston centred in the bore so the seal is not doing the guiding. When it wears, the piston drops onto the bore and the new seal follows it quickly.
  • Rod (gland) seal — seals the 120 mm rod where it leaves the cylinder.
  • Rod wiper / dust seal — scrapes concrete dust, grit and wash-down water off the rod before it reaches the rod seal. On a pump working in concrete, it does as much for seal life as the seal itself.
  • O-rings and backup rings — static sealing at the gland and piston, with backup rings behind the softer O-rings to stop them being squeezed out under pressure.
  • Scope — one 140/120 mm seal kit for concrete pump hydraulic cylinder normally covers one rebuild of one cylinder; if both drive cylinders are coming apart, plan for two and check your parts list before ordering.
  • Matching the old parts — seal profiles can differ between cylinder variants, so lay the old seals beside the new ones before anything goes in. If a profile does not line up, stop and check the number with us rather than forcing it.

Specifications

The reference for this hydraulic cylinder seal kit 140/120 mm is 086877008, and the sizes are a 140 mm bore with a 120 mm rod. Both have to agree with your cylinder — a number that looks close but belongs to another size will not fit, and a cylinder of the right size with a different seal profile will not seal. Start from the number you already have. Parts books list it against the cylinder group, and the bag or box the old seals came in usually carries it as well. Trust your own documentation over the machine's name: Putzmeister built several cylinder variants across its pump ranges, and the number on the machine is the reliable guide to which one you have. If the number is worn or unreadable, work from the cylinder itself. Measure the bore and the rod with a caliper, photograph the rod end and the gland, and note the details on the machine's type plate. Those three things are usually enough for us to identify the kit you need. One mix-up worth avoiding: this is not the E160/60 kit used on 160 mm bore, 60 mm rod cylinders. The two look alike in a photograph and share the same family of sealing components, but they belong to different cylinders, and ordering one for the other is an expensive wrong fit. On origin, plainly: this is an aftermarket kit, not a genuine Putzmeister-branded part. It is manufactured to the original dimensions so it can take the place of the OEM item, and the brand name and OEM number appear here only so you can identify what it replaces. If your maintenance rules call for genuine branded parts, this is not the kit to specify.

Related Parts to Inspect

  • Piston rod surface — scoring, pitting or a burr at the thread end will cut a new seal. If the rod is marked, it needs polishing or replacement before the kit goes in.
  • Cylinder bore — look for scores and a polished step where the piston has been running. New seals cannot hold on a scored bore, however carefully they are fitted.
  • Hydraulic oil and filter — milky, gritty or burnt-smelling oil will destroy a new set. If the machine has not had an oil and filter change, do it in the same visit.
  • Old seals — once a hydraulic cylinder seal set has been in service the rubber takes a set; keep the old parts only as a size reference when you compare them with the new ones, never as spares.
  • The second cylinder — if your pump has two drive cylinders, the other one carries the same hours. Check it while the circuit is already drained rather than opening the machine again next month.

Installation & Commissioning

  1. Clean the machine down first — a hydraulic cylinder seal set is easily ruined by grit falling into an open gland, so wash the concrete off the cylinder area before anything is opened.
  2. Release pressure and isolate — follow the pump manufacturer's shutdown procedure, lock off, and bleed the hydraulic circuit before any line is cracked.
  3. Open the cylinder and support the rod — cap the open ports, keep the rod straight and clean, and lay the parts out in the order they came off.
  4. Fit the seals with clean oil — lubricate lips and O-rings with the same oil the machine runs, and keep grease, grit and workshop dust away from the sealing faces.
  5. Protect the lips on assembly — tape the rod thread or slide a fitting sleeve over it so the rod seal is not cut as it passes back through the gland.
  6. Close and torque — tighten the gland to the manufacturer's torque figure rather than by feel.
  7. Refill and bleed — top up the reservoir to the specified level, run the cylinder through several full strokes at low pressure to push the air out, then recheck the level.
  8. Test and watch — run the machine under working pressure and look for weeping at the gland and around the ports. A dry rod after a few cycles is the sign the seals have seated.

Ordering, Payment & Delivery

  1. Send the details — the OEM number or pump model, the number of kits you need and the delivery country, by WhatsApp on +86 19545516660, by email to joak816@outlook.com, or through the contact form. A photo of the old seals or the cylinder plate shortens the check.
  2. We confirm and quote — we check the reference and the 140/120 size pair against your details and send a written quotation with pricing, packing and delivery terms.
  3. Payment — by T/T or L/C.
  4. Dispatch — we normally dispatch parts within 3–5 days after receiving your order.
  5. Shipping — Worldwide shipping, mostly by FedEx, DHL, EMS or UPS, with 3–7 days in transit. Public holidays, or events beyond our control such as an earthquake or a hurricane, can add a few days.
  6. Tracking — when the parcel ships we email the carrier name and tracking number, and you can follow it on the carrier's website. Please make sure the shipping address and contact details on your order are complete and correct.
  7. Check on arrival — open and inspect the kit as soon as it arrives. If something is wrong, contact us within 15 days of receipt and we will send the return address.
  8. Returns and refunds — the buyer pays return shipping unless the parts arrived faulty or damaged. Once the return reaches us and is confirmed, the refund goes back to your payment account within a few days.
  9. Catalog and product sheet — the current parts catalog and the sheet for this kit can be downloaded, or we can attach them to your quotation.
  10. Talk to a person — we have been a hydraulic cylinder seal kit supplier to pump workshops, fleets and parts distributors for more than 15 years. Send the machine details and we will answer before you commit.

Technical Support & Model Matching

Not sure a part will fit? Send us the OEM number, the machine model or a photo of the part you are replacing, and our technical team will check it against our records and confirm before you order. Founded in 2009, CZIC GROUP supplies construction machinery spares worldwide, with agents in more than 20 countries. We help buyers with part matching, fault diagnosis and installation or commissioning questions, before and after the sale.

FAQ

How do I check that this kit fits my cylinder?

Measure two things: the cylinder bore and the piston rod diameter. This kit is made for the 140/120 mm pair, so if either measurement differs it is the wrong one, even when the part number looks familiar. On a pump that is still assembled, both sizes are listed for the cylinder group in the machine's parts book.

Is this a genuine Putzmeister part?

No — we are an aftermarket hydraulic cylinder seal kit supplier, and this kit is built to replace the original rather than to carry the original brand. There is no OEM-branded box and no OEM paperwork with it. Workshops that run aftermarket parts order by the OEM number and check the size pair on arrival; if your maintenance procedure requires genuine parts with OEM documentation, plan for that instead.

Will it also fit the E160/60 cylinder?

No. The E160/60 kit is sized for cylinders with a 160 mm bore and a 60 mm rod, while this kit is built for the 140/120 mm pair, and neither will do the other's job. If you maintain several pump models, order each kit by its own number and size pair.

Can it be fitted on site, or does the cylinder have to come off?

Many drive cylinders can be resealed in place when there is room to draw the rod straight out and the gland is accessible. Where access is tight, or the rod needs proper support and inspection, the cylinder comes off and the job moves to the bench. Either way a hydraulic cylinder seal set still needs a clean working area, clean oil and a torque wrench for the gland — and the rod must come out in line, because side load on a fresh lip is what ruins a rebuild.

What makes a new seal kit fail early?

Almost always something around the seals rather than the seals themselves: grit or concrete dust reaching the rod, oil that is dirty or running too hot, a scored or pitted rod, a worn guide ring letting the piston run off centre, or a lip cut during assembly. Clean oil, a sound rod and careful fitting decide how long the kit lasts.

You can send money by T/T Or L/C
We have been committed to providing customers with fast, reliable logistics delivery services.
Shipping & Tracking
We normally dispatch parts within 3–5 days after receiving your order. Once your order ships, we send you the carrier name and tracking number.
Most orders ship by FedEx, DHL, EMS or UPS and take 3–7 days to arrive. Holidays or events beyond our control (such as earthquakes or hurricanes) may add a few days.
Please make sure your shipping address and contact details are complete and correct.
The carrier name and tracking number are in your shipping confirmation email, and you can track the parcel on the carrier's website.
Returns & Refunds
We offer a 15-day guarantee from receipt of the parts. Please check the parts as soon as they arrive.
Before returning anything, contact us by email and we will send you the return address. The buyer pays return shipping unless the parts arrived faulty or damaged.
Once we receive the return and confirm there is no problem, we refund you. The refund reaches your payment account within a few days.
Whatsapp:+86 19545516660
Email:joak816@outlook.com
  • 086877008 Hydraulic Cylinder Seal Kit 140/120mm

Download

CONTACT US

If you have any queries, get in touch today! Don't hesitate. We try to take the extra step for our customer satisfaction.
Name
Email *
Message
Leave a message
Name
Email *
Message
We use Cookie to improve your online experience. By continuing browsing this website, we assume you agree our use of Cookie.
Message Us