• 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR

283868001 Accumulator Bladder 6L NBR

No.283868001

Category: Putzmeister Spare Parts

Part Name: Accumulator Bladder

Spec: 6.0 L

OEM NO.: 283868001

  • Description

  • Payment Method

  • Shipping&Returns

  • Contact Us

Failure Symptoms & Diagnosis

SymptomWhat it usually meansWhat to do
Pump will not hold pressure after shutdownPrecharge has escaped, or the bladder has splitCheck the gas-valve pressure first, then inspect the bladder
Oil at the gas valve or charging portBladder wall has split and oil is being pushed into the gas sideStop the pump, replace the bladder, clean the gas side before recharging
Output feels rough, boom jerks at low speedAccumulator is no longer damping pulsationTest the precharge; if it will not hold, replace the bladder
Precharge drops again within days of rechargingPinhole or fatigue crack in the rubberReplace — recharging will not seal it
Bladder stretched or deformed on removalLong service, rubber fatigue, or precharge set too highFit a new NBR accumulator bladder and reset precharge to the figure in the pump manual
Knocking or noise from the accumulatorGas pocket has collapsed and the bladder is sitting on the valveInspect and replace
Oil running hot, pump labouringAccumulator is not absorbing shock loadingCheck precharge and bladder condition before the pump is worked hard again

Product Overview

283868001 is the replacement bladder for the 6L hydraulic accumulator for concrete pump hydraulic circuits — the flexible NBR bag that sits inside the steel shell and keeps the nitrogen precharge apart from the hydraulic oil. On every pressure stroke the bladder flexes so the accumulator can absorb pulsation, hold a reserve for the S-valve changeover and take the shock out of the hydraulic system. This is the bladder on its own. The steel housing, the gas valve and the fittings are not part of the order, which is what most workshops want: as long as the shell is sound and the gas valve seats properly, an accumulator bladder replacement brings the accumulator back into working condition for a fraction of the cost of a complete unit. Putzmeister names and OEM numbers appear here so you can match the part you are taking off; the fit itself is decided by the number stamped on the old bladder and by the 6.0 L volume of the housing. It suits pump distributors holding fast-moving hydraulic spares, service workshops doing accumulator repairs, and fleet maintenance teams who would rather change a bladder in the yard than wait for a complete accumulator to arrive.

Bladder vs Complete Accumulator

  • What wears out: the rubber bladder is the part that flexes, fatigues and eventually splits. A steel shell and gas valve normally outlast several bladders. - When the bladder alone is enough: the inside of the shell is clean and unpitted, the gas valve threads and seat are undamaged, and the trouble started as a slow pressure loss rather than impact damage — an accumulator bladder replacement is then all the repair needs. - When the assembly is the better buy: heavy corrosion or pitting inside the shell, a gas valve that will not seal even with a new bladder, or damaged threads left by an earlier repair. Ask us about the complete 6.0 L accumulator in that case. - What you are ordering: the moulded bladder with its neck, nothing else. We supply it as a hydraulic accumulator manufacturer and concrete pump parts supplier, so the shell, gas valve and fittings stay on your machine unless they are damaged.

NBR Bladder Construction

This NBR accumulator bladder is moulded in nitrile butadiene rubber because the material has to live in mineral hydraulic oil and flex through a very large number of pressure cycles without cracking. Nitrile resists oil swell, keeps its elasticity at normal hydraulic working temperatures and tolerates the light contamination that any working pump carries.

Two areas decide how long the part lasts. The neck, where the bladder seats into the gas valve, is the usual starting point for a leak: a neck that is not moulded squarely creeps and weeps even when the rest of the bladder is sound. The wall has to be thick enough to resist nitrogen diffusion yet flexible enough to fold without sharp creases — too stiff and the load transfers into the neck, too thin and the precharge disappears between services.

Volume is fixed by the housing. The 6L hydraulic accumulator for concrete pump assemblies this bladder serves takes the 6.0 L size only, and the dimensions follow the OEM reference rather than a generic pattern, which matters when an accumulator is being rebuilt to the original drawing.

If your pump runs fire-resistant or biodegradable hydraulic fluid rather than standard mineral oil, tell us before ordering. NBR is the right compound for mineral oil, but other fluids may call for a different elastomer, and it is far cheaper to check than to fit a bladder that swells in service.

Fitment Confirmation

  • Start with the number: the old bladder usually carries the OEM reference on the neck, or it is recorded against the accumulator plate. If it reads 283868001, this is the replacement. - Then the volume: the housing must be the 6.0 L size. A bladder from a smaller or larger accumulator will not hold the correct precharge, even when the neck looks similar. - Then the machine: pump model, build year, and the accumulator part number from the parts book where you have it. - If the number is unreadable: send photos of the old bladder next to a ruler, the accumulator plate and the pump rating plate, and we can usually work the size out from those.

Specifications

PropertyValue
Part nameAccumulator bladder
OEM reference283868001
Capacity6.0 L
MaterialNBR (nitrile butadiene rubber)
Part typeBladder only — housing and gas valve not included
Fits6L hydraulic accumulator housings on Putzmeister concrete pumps
Supply basisAftermarket accumulator bladder replacement, matched by OEM number
SystemConcrete pump hydraulic circuit
CategoryConcrete pump spare parts / hydraulic accumulator parts
Brand notePutzmeister is a trademark of its owner; OEM numbers are used for reference only

Installation & Precharge

  1. Park the machine on level ground, switch off, and release the hydraulic pressure. Discharge the nitrogen charge from the 6L hydraulic accumulator through the gas valve before anything is loosened — a charged accumulator stores enough energy to injure whoever opens it.
  2. Note the precharge pressure and the way the old bladder sits before dismantling, and cover the gas valve so grit cannot reach the seat.
  3. Take the accumulator off the machine if access is tight. Some installations allow the bladder to be changed in place, but the housing still has to come apart squarely.
  4. Lift out the old bladder and look inside the shell: sludge, corrosion pitting or a film of grit will shorten the life of the new bladder and should be cleaned out first.
  5. Seat the new bladder so the neck sits square in the gas valve with no twisting. Wipe the bore with clean hydraulic oil rather than grease, which can attack the rubber.
  6. Close the housing to the torque figure given in the pump manual, refit it to the machine and refill with clean hydraulic oil.
  7. Charge with dry nitrogen only — never oxygen or compressed air — to the precharge pressure your pump manufacturer specifies. Confirm it holds, run a few cycles, then re-check for leaks and precharge.

Ordering, Payment & Delivery

  1. Send the OEM number stamped on the old bladder, or the pump model plus a photo of the part. We confirm the match against our records before the order is placed — a hydraulic accumulator manufacturer works from numbers, not from descriptions.
  2. Payment is by T/T or L/C.
  3. Worldwide shipping: parts normally leave the warehouse within 3–5 days of receiving your order, by FedEx, DHL, EMS or UPS, with 3–7 days in transit. Holidays or events outside anyone's control, such as earthquakes or hurricanes, can add a few days.
  4. The carrier name and tracking number are emailed once the parcel ships so you can follow it on the carrier's website; please make sure the delivery address and contact details on the order are complete and correct.
  5. Open and check the part as soon as it arrives. You have 15 days from receipt to raise a problem with us; email first and we will send you the return address. The buyer pays return shipping unless the part arrived faulty or damaged, and the refund is issued once the return has been checked.
  6. Ask for the catalogue, extra photos of this bladder, or a quote on gas valves, seals and complete accumulators — WhatsApp +86 19545516660, email joak816@outlook.com.

Technical Support & Model Matching

Not sure a part will fit? Send us the OEM number, the machine model or a photo of the part you are replacing, and our technical team will check it against our records and confirm before you order. Founded in 2009, CZIC GROUP supplies construction machinery spares worldwide, with agents in more than 20 countries. We help buyers with part matching, fault diagnosis and installation or commissioning questions, before and after the sale.

FAQ

Can I reuse the gas valve and fittings from the old bladder?

In most cases yes. The bladder neck seats on the gas valve already fitted in the housing, so the valve, its cap and the fittings are cleaned and reused. What should not be reused is a valve with a scored seat or damaged threads — that will leak again with a new bladder in place, and the leak will look like a bladder fault. Inspect the seat while the housing is open.

Can the bladder be changed with the accumulator still on the pump?

Often yes, if there is room to open the housing squarely in place. On most 6L hydraulic accumulator for concrete pump installations the unit sits low on the frame and the work is done from underneath, so check access before starting. If the housing cannot be opened cleanly, take the accumulator off the machine. Either way the nitrogen charge must be released first.

Will a 4.0 L or 10.0 L bladder fit instead?

No. The bladder has to match the volume of the housing: a 6L hydraulic accumulator takes the 6.0 L bladder, and the smaller and larger accumulators take their own. A bladder of the wrong volume will not hold the correct precharge even if the neck happens to seat, so order by the number on the old part rather than by appearance.

What shortens bladder life?

Precharge set too high or too low, hydraulic oil running hot, a fluid the rubber is not suited to, and grit or water left inside the shell during an earlier repair. A bladder that fails within weeks of fitting usually supports one of those rather than to the part itself — check the precharge against the pump manual and clean the shell before the new bladder goes in.

Is this a genuine Putzmeister part?

No. It is an aftermarket replacement built to the OEM reference and supplied by a hydraulic accumulator manufacturer rather than by the machine maker. Putzmeister is a trademark of its owner, and the OEM number is used only so you can match the part you are removing.

You can send money by T/T Or L/C
We have been committed to providing customers with fast, reliable logistics delivery services.
Shipping & Tracking
We normally dispatch parts within 3–5 days after receiving your order. Once your order ships, we send you the carrier name and tracking number.
Most orders ship by FedEx, DHL, EMS or UPS and take 3–7 days to arrive. Holidays or events beyond our control (such as earthquakes or hurricanes) may add a few days.
Please make sure your shipping address and contact details are complete and correct.
The carrier name and tracking number are in your shipping confirmation email, and you can track the parcel on the carrier's website.
Returns & Refunds
We offer a 15-day guarantee from receipt of the parts. Please check the parts as soon as they arrive.
Before returning anything, contact us by email and we will send you the return address. The buyer pays return shipping unless the parts arrived faulty or damaged.
Once we receive the return and confirm there is no problem, we refund you. The refund reaches your payment account within a few days.
Whatsapp:+86 19545516660
Email:joak816@outlook.com
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR
  • 283868001 Accumulator Bladder 6L NBR

Download

CONTACT US

If you have any queries, get in touch today! Don't hesitate. We try to take the extra step for our customer satisfaction.
Name
Email *
Message
Leave a message
Name
Email *
Message
We use Cookie to improve your online experience. By continuing browsing this website, we assume you agree our use of Cookie.
Message Us